A great leap forward in accuracy occurred in 1657 with the addition of the balance spring to the balance wheel, an invention disputed both at the time and ever since between Robert Hooke and Christiaan Huygens. Prior to this, the only force limiting the back and forth motion of the balance wheel under the force of the escapement was the wheel's inertia. This caused the wheel's period to be very sensitive to the force of the mainspring. The balance spring made the balance wheel a harmonic oscillator, with a natural 'beat' resistant to disturbances. This increased watches' accuracy enormously, reducing error from perhaps several hours per day[12] to perhaps 10 minutes per day,[13] resulting in the addition of the minute hand to the face from around 1680 in Britain and 1700 in France. The first thing to be improved was the escapement. The verge escapement was replaced in quality watches by the cylinder escapement, invented by Thomas Tompion in 1695 and further developed by George Graham in the 1720s. In Britain a few quality watches went to the duplex escapement, invented by Jean Baptiste Dutertre in 1724. The advantage of these escapements was that they only gave the balance wheel a short push in the middle of its swing, leaving it 'detached' from the escapement to swing back and forth undisturbed during most of its cycle.During the same period, improvements in manufacturing such as the tooth-cutting machine devised by Robert Hooke allowed some increase in the volume of watch production, although finishing and assembling was still done by hand until well into the 19th century. At Vacheron Constantin, Geneva, Georges-Auguste Leschot (1800 1884), pioneered the field of interchangeability in clockmaking by the invention of various machine tools.[14] In 1830 he designed an anchor escapement, which his student, Antoine Lechaud, later mass-produced. He also invented a pantograph, allowing some degree of standardisation and interchangeability of parts on watches fitted with the same calibre.The British had predominated in watch manufacture for much of the 17th and 18th centuries, but maintained a system of production that was geared towards high quality products for the elite.[15] Although there was an attempt to modernise clock manufacture with mass production techniques and the application of duplicating tools and machinery by the British Watch Company in 1843, it was in the United States that this system took off. Aaron Lufkin Dennison started a factory in 1851 in Massachusetts that used interchangeable parts, and by 1861 was running a successful enterprise incorporated as the Waltham Watch Company.The railroads' stringent requirements for accurate watches to safely schedule trains drove improvements in accuracy. The engineer Webb C. Ball, established around 1891 the first precision standards and a reliable timepiece inspection

The Enlightenment view of watches as scientific instruments brought rapid advances to their mechanisms. The development during this period of accurate marine chronometers to determine longitude during sea voyages produced many technological advances that were later used in watches. It was found that a major cause of error in balance wheel timepieces was changes in elasticity of the balance spring with temperature changes. This problem was solved by the bimetallic temperature compensated balance wheel invented in 1765 by Pierre Le Roy and improved by Thomas Earnshaw. This type of balance wheel had two semicircular arms made of a bimetallic construction. If the temperature rose, the arms bent inward slightly, causing the balance wheel to rotate faster back and forth, compensating for the slowing due to the weaker balance spring. This system, which could reduce temperature induced error to a few seconds per day, gradually began to be used in watches over the next hundred years. The going barrel invented in 1760 by Jean-Antoine Lepine provided a more constant drive force over the watch's running period, and its adoption in the 19th century made the fusee obsolete. Complicated pocket chronometers and astronomical watches with many hands and functions were made during this period.The lever escapement, invented by Thomas Mudge in 1759 and improved by Josiah Emery in 1785, gradually came into use from about 1800 onwards, chiefly in Britain; it was also adopted by Abraham-Louis Breguet, but Swiss watchmakers (who by now were the chief suppliers of watches to most of Europe) mostly adhered to the cylinder until the 1860s. By about 1900, however, the lever was used in almost every watch made. In this escapement the escape wheel pushed on a T shaped 'lever', which was unlocked as the balance wheel swung through its centre position and gave the wheel a brief push before releasing it. The advantages of the lever was that it allowed the balance wheel to swing completely free during most of its cycle; due to 'locking' and 'draw' its action was very precise; and it was self-starting, so if the balance wheel was stopped by a jar it would start again.Jewel bearings, introduced in England in 1702 by the Swiss mathematician Nicolas Fatio de Duillier, also came into use for quality watches during this period. Watches of this period are characterised by their thinness. New innovations, such as the cylinder and lever escapements, allowed watches to become much thinner than they had previously been. This caused a change in style. The thick pocketwatches based on the verge movement went out of fashion and were only worn by the poor, and were derisively referred to as "onions" and "turnips".

The American clock industry, with scores of companies located in Connecticut's Naugatuck Valley, was producing millions of clocks, earning the region the nickname, "Switzerland of America".[18] The Waterbury Clock Company was one of the largest producers for both domestic sales and export, primarily to Europe.[19] Today its successor, Timex Group USA, Inc. is the only remaining watch company in the region.From about 1860, key winding was replaced by keyless winding, where the watch was wound by turning the crown. The pin pallet escapement, an inexpensive version of the lever escapement invented in 1876 by Georges Frederic Roskopf was used in cheap mass-produced watches, which allowed ordinary workers to own a watch for the first time; other cheap watches used a simplified version of the duplex escapement, developed by Daniel Buck in the 1870s.During the 20th century, the mechanical design of the watch became standardized, and advances were made in materials, tolerances, and production methods. The bimetallic temperature-compensated balance wheel was made obsolete by the discovery of low-thermal-coefficient alloys invar and elinvar. A balance wheel of invar with a spring of elinvar was almost unaffected by temperature changes, so it replaced the complicated temperature-compensated balance. The discovery in 1903 of a process to produce artificial sapphire made jewelling cheap. Bridge construction superseded 3/4 plate construction.

The Enlightenment view of watches as scientific instruments brought rapid advances to their mechanisms. The development during this period of accurate marine chronometers to determine longitude during sea voyages produced many technological advances that were later used in watches. It was found that a major cause of error in balance wheel timepieces was changes in elasticity of the balance spring with temperature changes. This problem was solved by the bimetallic temperature compensated balance wheel invented in 1765 by Pierre Le Roy and improved by Thomas Earnshaw. This type of balance wheel had two semicircular arms made of a bimetallic construction. If the temperature rose, the arms bent inward slightly, causing the balance wheel to rotate faster back and forth, compensating for the slowing due to the weaker balance spring. This system, which could reduce temperature induced error to a few seconds per day, gradually began to be used in watches over the next hundred years. The going barrel invented in 1760 by Jean-Antoine Lepine provided a more constant drive force over the watch's running period, and its adoption in the 19th century made the fusee obsolete. Complicated pocket chronometers and astronomical watches with many hands and functions were made during this period.The lever escapement, invented by Thomas Mudge in 1759 and improved by Josiah Emery in 1785, gradually came into use from about 1800 onwards, chiefly in Britain; it was also adopted by Abraham-Louis Breguet, but Swiss watchmakers (who by now were the chief suppliers of watches to most of Europe) mostly adhered to the cylinder until the 1860s. By about 1900, however, the lever was used in almost every watch made. In this escapement the escape wheel pushed on a T shaped 'lever', which was unlocked as the balance wheel swung through its centre position and gave the wheel a brief push before releasing it. The advantages of the lever was that it allowed the balance wheel to swing completely free during most of its cycle; due to 'locking' and 'draw' its action was very precise; and it was self-starting, so if the balance wheel was stopped by a jar it would start again.Jewel bearings, introduced in England in 1702 by the Swiss mathematician Nicolas Fatio de Duillier, also came into use for quality watches during this period. Watches of this period are characterised by their thinness. New innovations, such as the cylinder and lever escapements, allowed watches to become much thinner than they had previously been. This caused a change in style. The thick pocketwatches based on the verge movement went out of fashion and were only worn by the poor, and were derisively referred to as "onions" and "turnips".